2 Stroke Outboard Engine CDI Ignition Manual Starting Boat Engine Water Cooling | eBay.Item #, Manual Ignition Chamber - Orion Safety

Looking for:

Ignition manual -  

Click here to DOWNLOAD

     

- Ignition manual

 

Dust or grease accumulation can cause failure of control operation. Avoid dust or grease accumulation in terminal connection areas of the control. Failure of the spark ignition control can occur as a result of contact with corrosive chemicals, either directly or through the air.

Avoid corrosive chemical contact with the control. Excessively high temperatures can damage the control and cause failure. Assure the maximum ambient temperature at the control does not exceed the maximum temperature rating. The appliance and venting system must be subject to a safety check before the spark ignition control is installed. If an unsafe condition is detected, remove all power from the appliance and correct the unsafe condition before proceeding with the installation.

First disconnect all power to the old control module. Disconnect and label all wire connections from the old control module. Remove the old control module from its mounting location. Mount the control in the same location as the old module, if installed as a replacement, or use the control module as a template to mark the mounting hole pattern.

Drill new holes as required and fasten securely with two 6 sheet metal or machine screws. The control must be mounted with the terminals facing down, facing sideways left, or facing sideways right. Do not mount the control with the terminals facing the upward position in order to help prevent exposure to water, moisture, corrosive chemicals, grease, and dust.

Make sure the thermostat is in the OFF position to assure there is no call for heat. All wiring must conform to local and national electrical codes.

Do not allow the spark leadwire to rest against grounded metal surfaces. The burner must be properly grounded in order to accurately sense flame. A proper connection must exist between the spark terminal and HV spark gap. However, an open circuit between the spark terminal and spark wire spark wire not connected may result in an on board HV discharge for which the circuit is designed to handle without damage.

Universal models come with external flame sense active. For hardware types 01 thru 04, when using external flame sense, removing the jumper plug by clipping the wire close to the unit is recommended. The dip switches remain active until 10 consecutive power cycles occur without a change in any dip switch setting.

Once this occurs, timing specifications are locked, dip switches become inactive, and cannot further be used to change timing specifications.

Heating cycle starts when a call for heat from thermostat supplies power to the spark ignition control. The control waits for a time delay equal to pre-purge time. Upon expiration of pre-purge time, the control enters trial for ignition mode.

The control initiates sparking, opens the pilot valve for IP controls or the main valve for DSI controls, and begins the trial for ignition time period. There is no better way to protect your investment and future-proof your system than by adding a support plan to your Ignition purchase. Choose from three different support levels in our updated program to fit your specific needs.

You don't need to buy it to try it; with Ignition you can design, build, and test your entire project for free as long as you want. Call Us Schedule a Demo. Ignition Exchange Discover Ignition resources. Services Training Pricing.

Distributors International Distributors. Strategic Partner Cirrus Link Solutions. Education Educational Engagement. Download it today. It represents our full vision of what The New SCADA could be, and is the platform that all of our customers will want to leverage for their next-generation solutions. For the Plant Floor Ignition 8.

Watch the video. A New Perspective for the Plant Floor With Perspective, you can create beautiful, mobile-responsive industrial applications that run natively on any mobile device and web browser. Design for Multiple Screen Sizes at the Same Time Save development time by designing a single Perspective application that displays beautifully on screens of any size. Customize Your Symbols Visual options such as supporting text, animation, and device orientation can be defined to fit your project.

Tag Browser Built Right In You can easily access and analyze historical tag data right from the session window, no additional development necessary.

Data-Driven Table Easily view dynamic chart data in a table format for quick analysis, all within the session. Browsing is a Breeze In 8. For New Users Ignition 8. Learn by Deconstructing Quick Start comes with a pre-configured sample project that includes core Ignition features for you to use, break apart, add to, and more to help you better understand and visualize Ignition.

Explore Advanced Features Learn about concepts like screen layout, components, and Python scripting. Follow Tutorials in the Gateway Follow along with new tutorials that help guide you through gateway configuration and project set-up. Visit the University. For Enterprise Ignition 8 introduced big updates for developing large-scale systems, including easy project management, and collaborative concurrent development.

Control User Access Easily control access to system areas for different users with the click of a button. The final goal of the content and information provided here is to help you gain understanding of Ignition concepts and to accomplish tasks within Ignition so that you can be productive and effective while working on your own projects.

You can search for specific items, or browse through the navigation tree to find the answers you need. The table of contents is organized so you can easily find answers to your questions on all the Ignition features, modules, functions, and anything else you may be looking for.

The Getting Started section provides a broad overview and information relating to Modules , architectures , installation , and a quick start guide. This core User Manual section is closely tied with the Inductive University so you can have a conceptual understanding from this manual and a visual walk-through of the feature in the videos. Just look for video links on the right side of the page to jump to the University. Finally, in the Appendix , you'll find an exhaustive list of all the Components , Expressions , and Scripting Functions in Ignition.

This section of the Ignition User Manual shows all of the documentation for Ignition in a format that is listed by feature or section of the platform. It provides reference and concept information along with step-by-step instructions on how to do just about everything in Ignition. Throughout this online help manual, you will find links to the various Inductive University videos on the right side of the screen.

These videos correspond to the information in that page or section. This way, you can get a conceptual understanding from the information provided here, and a visual walk-through of the feature by watching the videos. The video links will look like the one to the right of this paragraph. Take a look at the navigation section on the left and poke around, or use the search bar at the top of the navigation.

To get back to this manual later, you can access it in three ways:. To access from a web browser , go to docs. The Getting Started section has all the basic information on Ignition.

If you want a general overview and some basic steps to get Ignition up and running, this is the place to start. Are you looking for something that has changed? Or maybe you want to see the things we have been adding to Ignition? Check out the New in this Version page for a list of improvements for each version. A Glossary of common terms found in Ignition and in the industry. Anyone looking to create a new module should start here. Inductive Automation is proud to have a Partner Program that allows others to create modules to enhance Ignition's functionality.